With an accout for my.chemeurope.com you can always see everything at a glance – and you can configure your own website and individual newsletter.

To use all functions of this page, please activate cookies in your browser.

Green electronics: Making electronic components at least partly from a natural raw material like wood seems an obvious solution.

Sustainable electronic components can be made from wood with the help of a novel process that uses a laser to engrave electrically conductive structures on veneers. A research team at Empa and at ETH’s Institute for Building Materials has developed a practical and versatile method for making wooden surfaces electrically conductive.

Non-biodegradable electronic waste continues to accumulate year after year. For that reason, making electronic components at least partly from a natural raw material like wood seems an obvious solution. But it’s easier said than done. For one thing, wood is naturally an electrical insulator. It also has a complex structure, making it a challenge to achieve homogeneous electrical properties during large-scale fabrication.

Now, a research team  at Empa and at ETH’s Institute for Building Materials has developed a practical and versatile method for making wooden surfaces electrically conductive by graphitising them. In this way, devices such as touch panels and sensors can be produced on a large scale with great efficiency. The trick is to pretreat the wood with an ink containing iron. The project, led by Ingo Burgert and Guido Panzarasa, was supported by the Swiss National Science Foundation.

To make conductive structures on wood, the new method improves an existing process called laser-induced graphitization. A laser can engrave fine lines into wooden boards, or veneers. In this process, the energy of the laser beam heats the wood, causing a series of pyrolytic events leading to the formation of electrically conductive graphite. However, the obtained conductive patterns are irregular in depth and width, and there is also a fire hazard due to overheating. Often, multiple post-processing laser steps are needed as well. “The density of wood varies depending on the tree species and growth,” says Christopher Dreimol, first author of the study. “The result can be very uneven graphitization.”

The research team thus came up with the idea of using iron as a catalyst to enable a gentler process and a much more homogeneous surface. Searching for a biologically based catalyst material, Dreimol was inspired by the iron-gall ink, a mixture of iron salt and tannins used as early as the Middle Ages for writing. After optimizing the recipe, Dreimol coated a variety of wood veneers with a thin layer of the ink and then subjected them to the laser treatment.

The ink layer had the desired effect. The patterns engraved after just one pass showed a more uniform structure and conductivity, regardless of differences in the wood structure and type. “Because of the ink, the wood is transformed so quickly into graphite that there is less thermal damage and no risk of fire,” says Dreimol. In addition, much less wood is ablated. The patterns are only a few micrometers deep and can thus be engraved into the thinnest veneer without actually damaging it.

The team then used their new method to produce trial electronic components from spruce, cherry and beech veneers less than half a millimeter thick. According to Dreimol, bendable strain sensors could be integrated discreetly into load-bearing wood components in buildings, allowing for constant monitoring of their structural health. The researchers were also able to make the wafer-thin wood glow by means of an electroluminescent layer. Despite the grain of the veneer, homogeneous illumination was achieved. This is an unprecedented result and could be used in applications such as backlighting for displays or for advertisements and control panels. For the electroluminescent wood, the researchers used still conventional wiring and electronic components, however. In the future, these could also be partially replaced by conductive wood.

The next step is to refine and further develop the method for large-scale use: “The fact that we can now process relatively large areas in an acceptable amount of time is the first step towards industrializing electronic components made of wood,” says Dreimol.

You are currently not logged in to my.chemeurope.com . Your changes will in fact be stored however can be lost at all times.

My notice: Add / edit notice

my watchlist Cancel Save notice

In control of chaos: On the hunt for high entropy crystals

Crystals consisting of wildly mixed ingredients - so-called high-entropy materials - are currently attracting growing scientific interest. Their advantage is that they are particularly stable at extremely high temperatures and could be used, for example, for energy storage and chemical prod ... more

A paper battery with water switch

A team of researchers at Empa developed a water-activated disposable paper battery. The researchers suggest that it could be used to power a wide range of low-power, single-use disposable electronics – such as smart labels for tracking objects, environmental sensors and medical diagnostic d ... more

Graphene dust not harmful, study finds

Graphene-based particles released from polymer composites after abrasion induce negligible health effects. Under the leadership of Empa, an international research team of the Graphene Flagship project conducted a study on the health risks of graphene-containing nanoparticles and recently pu ... more

First step to produce a cheap aquous electrolyte for powerful rechargeable batteries: Seven grams of sodium FSI (precise name: sodium bis(fluorosulfonyl)imide) and one gram of water produce a clear saline solution with an electrochemical stability of up to 2.6 volts – twice as much as other ... more

Read what you need to know about our industry portal chemeurope.com.

Find out more about the company LUMITOS and our team.

Find out how LUMITOS supports you with online marketing.

© 1997-2022 LUMITOS AG, All rights reserved